Component: winbox
2,119 changelog entries across 311 version(s)
Releases by channel (stacked)
- added "add-relay-info" and "relay-info-remote-id" to DHCP relay;
- added H flag to "/ip arp" ;
- added missing "use-fan2" and "active-fan2" to "/system health";
- allow shorten bytes to k,M,G in bridge firewall just like in “/ip firewall”;
- do not hide 00:00:00:00:00:00 MAC address in unpublished ARPs;
- fixed matching "connection-state=untracked" connections;
- fixed typo in “/system resources pci” list;
- make "power-cycle-after" show correct value;
- updated fan management menu;
- added "make-static" to IPv6 DHCP server bindings;
- added "prefix-pool" to DHCPv6 server binding;
- added IPsec to radius services;
- added upstream flag to IGMP proxy interfaces;
- allow to specify "connection-bytes" & "connection-rate" for any protocol in “/ip firewall” rules;
- allow to specify "sip-timeout" under ip firewall service-ports;
- do not create empty rates.vht-basic/supported-mcs if not specified in CAPsMAN;
- hide "nat-traversal" setting in IPsec peer if IKEv2 is selected;
- show dynamic IPv6 pools properly;
- show errors on IPv6 addresses;
- specify metric for “/ip dns cache-used” setting;
- added "Complete" flag to arp table;
- added "make-static" to IPv6 DHCP server bindings;
- added "prefix-pool" to DHCPv6 server binding;
- added upstream flag to IGMP proxy interfaces;
- allow to enable/disable traffic flow targets;
- allow to specify "connection-bytes" & "connection-rate" for any protocol in “/ip firewall” rules;
- allow to specify "sip-timeout" under ip firewall service-ports;
- do not allow to set "loop-protect-send-interval" to 0s;
- do not create empty rates.vht-basic/supported-mcs if not specified in CAPsMAN;
- fixed crash when legacy Winbox version was used;
- fixed default values for interface "loop-protect-disable-time" and "loop-protect-send-interval";
- fixed missing "IPv6/Settings" menu;
- fixed typo in "propagate-ttl" setting;
- properly show VHT basic and supported rates in CAPsMAN;
- show all related HT tab settings in 2GHz-g/n mode;
- show dynamic IPv6 pools properly;
- show errors on IPv6 addresses;
- show proper ipv6 connection timeout;
- specify metric for “/ip dns cache-used” setting;
- added "Complete" flag to arp table;
- added "untracked" option to firewall "connection-state" setting;
- added Dude icon to Dude menu;
- allow to enable/disable traffic flow targets;
- allow to run profile from "/system resources" menu;
- allow to specify interface for leds with "interface-speed" trigger;
- do not allow to set "loop-protect-send-interval" to 0s;
- do not show hotspot user profile incoming and outgoing filters and marks as set if there is no value specified;
- fixed crash when legacy Winbox version was used;
- fixed default values for interface "loop-protect-disable-time" and "loop-protect-send-interval";
- fixed missing "IPv6/Settings" menu;
- fixed typo in "propagate-ttl" setting;
- make cert signing include provided ca-crl-host;
- moved ipsec peer "exchange-mode" to General tab;
- properly show VHT basic and supported rates in CAPsMAN;
- removed spare values from loop-protect menu;
- show all related HT tab settings in 2GHz-g/n mode;
- show primary and secondary ntp addresses as 0.0.0.0 if none are set;
- show proper ipv6 connection timeout;
- recognize properly tcp in traffic-generator packet-template header type;
- show HT MCS tab if 2GHz-G/N band is used;
- added led settings menu;
- fixed missing switch menu for mmips devices;
- added loop-protect settings;
- added passthrough state to web-proxy;
- allow to unset http-proxy field for sstp client;
- do not show health menu on RB951-2n;
- fixed typo in dhcpv6 relay (DCHP to DHCP);
- show address expiration time in dhcp client list;
- fixed multiline read only fields not displaying new line characters;
- fixed raw firewall showing jump targets from filter chains;
- hide ethernet flow control settings for interfaces which does not support them;
- removed health menu from devices that do not support it;
- removed L2MTU field for PPP interfaces;
- removed L2MTU field from PPP server binding settings;
- removed unset button for L2MTU field;
- show firmware-type in routerboard window;
- added auto refresh for BFD neighbors;
- added comment field support for switch vlan menu;
- added default-authentication parameter for wireless station modes;
- added src-address field for traffic-flow target;
- adjust on-event field dynamically depending on window size;
- adjusted allowed values for http-proxy field;
- disabled MRRU by default for PPP interfaces;
- display actual-mtu for tunnels in interfaces window;
- fixed disconnect when no windows were opened for a while in unsecure mode;
- make queue tree default queue type default-small;
- added 2ghz-g/n band for wireless-rep;
- added icons to bridge filter actions similar to ip firewall;
- added support for ipv6 dhcp relay;
- allow to reorder hotspot walled-garden & walled-garden-ip rules;
- do not allow to specify vlan-mode=no-tag in capsman datapath config;
- do not show filter for combined fields like bgp-vpn4 RD;
- do not show mode setting for WDS interfaces;
- fixed crash on disconnect in secure mode;
- fixed crash when using ctrl+d;
- fixed safe mode;
- improve filtering on list fields;
- report correctly dude users in active users list;
- set default sa-learning value to "yes" for CRS Ingress VLAN Translation rules;
- show action column as first in bridge firewall;
- show error when telnet is not allowed because of permissions;
- show voltage in Health only if there actually is voltage monitor;
- show voltage in Health only if there actually is voltage monitor;
- added "pw-type" to "/interface vpls bgp-vpls" menu;
- added "use-control-word" and "pw-mtu" to "/interface vpls cisco-bgp-vpls" menu;
- added /interface wireless setup-repeater;
- added all the rates settings to the capsman;
- added flip-screen option to lcd settings;
- added init-delay option to routerboard settings;
- added ipv6 firewall missing log option;
- added missing eap-ttls-mschamv2 method to wireless security profile;
- added mtu=auto support to eoipv6 tunnel;
- added sfp-mac for GPON interfaces;
- added support for new settings from wireless-rep package;
- added support for route action in mangle rules;
- allow to set additional-network-modes;
- allow to set multiple dh-groups;
- disable autostart for wireless scan,snooper,align etc. on open;
- do not show "enable-jumper-reset" setting on devices without serial port;
- do not show real-tx-power column in current-tx-power by default;
- fixed unset options in /routing ospf interface menu;
- hotspot default-trial user shows profile as "unknown" in Winbox;
- improved winbox connection loss detection, fixes winbox safe mode;
- limit ospf key to 16 symbols;
- make additional-network-mode optional for lte interface;
- make build with latest lte changes;
- make mrru disabled and set mtu+mru to auto by default on new servers;
- show "usb-power-reset" option on all boards that have it;
- increased minimal required winbox version to 3.4;
- allow to show revoked & authority flags at the same time;
- correctly recognise if there is need to report fan information under system health;
- do not use area v2 names instead of ospf v3 area names;
- make mac-winbox work with RB850.
- allow to set multiple dh-groups;
- do not show fan statuses in passive cooling CCR1009;
- fixed typo in "echo reply";
- fixed unset options in /routing ospf interface menu;
- added factory-firmware field to system/routerboard;
- fixed email address saving;
- fixed multi value field display (i.e. web proxy ports);
- fixed incomplete ARP entries are not refreshed;
- added + & - to IGMP proxy MFC;
- allow to specify traffic-monitor threshold in k & M units + specify that those are bits;
- do not send any changes on OK button press if nothing has been changed;
- fixed tab names to correspond to console;
- renamed power-cycle-ping-interval to power-cycle-ping-timeout;
- show dhcp server name in dhcp leases;
- show fast-path per interface counters;
- show only actual switch-cpu ports in switch setting combobox;
- show properly route-distinguisher for bgp vpn4;
- include FP in fast-path column names;
- allow to specify amsdu-limit & amsdu-threshold on 11n wifi cards;
- added multicast-buffering & keepalive-frames settings to wireless interfaces;
- show Common-Name of certificates in certificate list;
- added units to PCQ queue fields;
- fixed possible busy-loop on v2.x with latest 6.34RC versions;
- add extra items automatically to multi-line fields if at least one of them is required;
- implemented full ipv6 dhcp client;
- update blocked flag if user changed blocked field in dhcp server lease;
- added + & - to IGMP proxy MFC;
- added LCD menu for RB3011;
- allow to specify traffic-monitor threshold in k & M units + specify that those are bits;
- show fast-path per interface counters.
- do not send any changes on OK button press if nothing has been changed;
- renamed power-cycle-ping-interval to power-cycle-ping-timeout;
- dropped support for winbox v3.0beta and v3.0rc (use winbox v3.0);
- added allow-fast-path to eoip, gre & ipip;
- do not show power-cycle properties on non poe ports;
- make sure that all setting names get shown in full;
- added poe power-cycle-ping settings to ethernet interfaces;
- added vlan-mode & vlan-id to virtual-ap interface;
- added timeout column to ipv6 address lists;
- show SFP Tx/Rx Power properly;
- added min-links to bonding interface;
- do not show health menu on RB951Ui-2HnD;
- added support for Login-Timeout & MAC-Auth-Mode in hotspot;
- make user ssh key import work again;
- fix to allow cpu-port as mirror-target
- allow to specify dns name in all the tunnels;
- make directed broadcasts work for neighbor discovery;
- Shift+Ins & Shift+Del did not work in multi entry fields;
- allow to specify ipv6 address in traffic flow target;
- allow to specify eap-radius-accounting in CAPsMAN;
- allow to enter dns name in email server;
- make console notice correct screen size;
- refetch hotspot walled garden hit counter;
- added client-connections & server-connections to web proxy status;
- fixed context menu actions to apply to all selected items;
- fixed wireless interface l2mtu (VirtualAP and WDS interface creation in winbox)
- fixed multiple firewall rule moving in Winbox 2
- restrict reversed ranges in dst-port under firewall
- added filtering by dscp to torch;