Component: ethernet

6.39.3 Long-term 2017-Oct-12 (8 years ago)

• fixed occasional broken interface order after reset/first boot;
• fixed rare linking problem with forced 10Mbps full-duplex mode;

6.41rc34 Testing 2017-Sep-27 (8 years ago)

• removed "master-port" parameter;

6.38.7 Long-term 2017-Jun-20 (9 years ago)

• fixed "loop-protect" on "master-port";
• fixed rare switch chip hang (could cause port flapping);

6.39 Stable 2017-Apr-27 (9 years ago)

• added "voltage-too-low" status for single port power injector devices;
• fixed "loop-protect" on "master-port";
• fixed rare switch chip hang (could cause port flapping);
• fixed unnecessary power cycle of powered device when changing any poe-out related setting on single port power injector devices;
• renamed "rx-lose" to "rx-loss" in ethernet statistics;
• reversed poe-priority on hEX PoE and OmniTIK 5 PoE to make "poe-priority" consistent to all other RouterOS priorities;

6.38 Stable 2016-Dec-30 (9 years ago)

• added "k" and "M" unit support to Ethernet Bandwidth setting;
• fixed "tx-fcs-error" on SFP+ interfaces when loop-protect is enabled;

6.37.2 Stable 2016-Nov-08 (9 years ago)

• fixed interface speed reporting for x86 in log after reboot or if "disable-running-check=yes";
• fixed potential loopprotect crash;

6.37 Stable 2016-Sep-23 (9 years ago)

• added support for LAN9514 ethernet dongle;
• allow to force mtu value when actual-mtu is already the same;
• fixed loop-protect on bridged ports;
• fixed never ending loop in CDP packet processing;
• fixed rare kernel failure on non-switch ethernet reset;
• rb44ge now have disabled-running-check=no by default;

6.36 Stable 2016-Jul-20 (10 years ago)

• fixed incorrect ether1 link speed after reboot on rb4xx series routers;
• fixed memory leak when setting interface without changing configuration;

6.35.4 Stable 2016-Jun-09 (10 years ago)

• fixed memory leak when setting interface without changing configuration;

6.34.5 Long-term 2016-May-27 (10 years ago)

• do not allow mtu to be higher than l2mtu and l2mtu to be higher than max-l2mtu (reduce automatically on upgrade if it was wrong before);

6.35.1 Stable 2016-Apr-25 (10 years ago)

• do not allow mtu to be higher than l2mtu and l2mtu to be higher than max-l2mtu (reduce automatically on upgrade if it was wrong before);

6.35 Stable 2016-Apr-14 (10 years ago)

• add option to see S-GPON-ONU module, GPON side SN in "/int eth mon sfp#";
• do not allow to set self as master port;

6.34.4 Stable 2016-Mar-24 (10 years ago)

• fixed Netmetal, QRT, DynaDish, SXT ac linking at 10/100Mbps (introduced in 6.34.x);

6.32.4 Long-term 2016-Feb-09 (10 years ago)

• fixed link resetting on power-cycle-ping value change;

6.33.3 Stable 2015-Dec-03 (10 years ago)

• fixed 10/100Mbps auto-negotiation fails on RB922UAGS ether1 (introduced in v6.33.2);

6.33.2 Stable 2015-Nov-27 (10 years ago)

• fixed link resetting on power-cycle-ping value change;

6.32.2 Stable 2015-Sep-17 (10 years ago)

• added support for new ASIX USB Ethernet dongles;

6.11 Stable 2014-Mar-20 (12 years ago)

• added option to enable rx/tx flow control (will be disabled by default);
• added ability to specify advertised modes for copper ports;