Component: ethernet
100 changelog entries across 50 version(s)
Releases by channel (stacked)
- added support for 25Gbps and 40Gbps rates;
- fixed running (R) flag not present on x86 interfaces and CHR legacy adapters;
- increased loop warning threshold to 5 packets per second;
- added "tx-rx-1024-max" counter to Ethernet stats;
- fixed packet forwarding when SFP interface is disabled on hEX S;
- added "tx-rx-1024-max" counter to Ethernet stats;
- fixed IPv4 and IPv6 packet forwarding on IPQ4018 devices;
- fixed linking issues on wAP ac, RB750Gr2 and Metal 52 ac (introduced in v6.43rc52);
- fixed packet forwarding when SFP interface is disabled on hEX S;
- fixed VLAN1 forwarding on RB1100AHx4 and RB4011 devices;
- improved per core ethernet traffic classificator on mmips devices;
- fixed VLAN1 forwarding on RB1100AHx4 and RB4011 devices;
- do not show "combo-state" field if interface is not SFP or copper;
- properly handle Ethernet interface default configuration;
- improved large packet handling on ARM devices with wireless;
- removed obsolete slave flag from "/interface vlan" menu;
- improved large packet handling on ARM devices with wireless;
- removed obsolete slave flag from "/interface vlan" menu;
- removed "master-port" parameter;
- fixed occasional broken interface order after reset/first boot;
- fixed rare linking problem with forced 10Mbps full-duplex mode;
- fixed "loop-protect" on "master-port";
- fixed rare switch chip hang (could cause port flapping);
- added "voltage-too-low" status for single port power injector devices;
- fixed "loop-protect" on "master-port";
- fixed rare switch chip hang (could cause port flapping);
- fixed unnecessary power cycle of powered device when changing any poe-out related setting on single port power injector devices;
- renamed "rx-lose" to "rx-loss" in ethernet statistics;
- reversed poe-priority on hEX PoE and OmniTIK 5 PoE to make "poe-priority" consistent to all other RouterOS priorities;
- added "k" and "M" unit support to Ethernet Bandwidth setting;
- fixed "tx-fcs-error" on SFP+ interfaces when loop-protect is enabled;
- fixed interface speed reporting for x86 in log after reboot or if "disable-running-check=yes";
- fixed potential loopprotect crash;
- added support for LAN9514 ethernet dongle;
- allow to force mtu value when actual-mtu is already the same;
- fixed loop-protect on bridged ports;
- fixed never ending loop in CDP packet processing;
- fixed rare kernel failure on non-switch ethernet reset;
- rb44ge now have disabled-running-check=no by default;
- fixed incorrect ether1 link speed after reboot on rb4xx series routers;
- fixed memory leak when setting interface without changing configuration;
- fixed memory leak when setting interface without changing configuration;
- do not allow mtu to be higher than l2mtu and l2mtu to be higher than max-l2mtu (reduce automatically on upgrade if it was wrong before);
- do not allow mtu to be higher than l2mtu and l2mtu to be higher than max-l2mtu (reduce automatically on upgrade if it was wrong before);
- add option to see S-GPON-ONU module, GPON side SN in "/int eth mon sfp#";
- do not allow to set self as master port;
- fixed Netmetal, QRT, DynaDish, SXT ac linking at 10/100Mbps (introduced in 6.34.x);
- fixed link resetting on power-cycle-ping value change;
- fixed 10/100Mbps auto-negotiation fails on RB922UAGS ether1 (introduced in v6.33.2);
- fixed link resetting on power-cycle-ping value change;
- added support for new ASIX USB Ethernet dongles;
- added option to enable rx/tx flow control (will be disabled by default);
- added ability to specify advertised modes for copper ports;