Search changelog entries
| Component | Change |
|---|---|
| dhcp | reduced resource usage of DHCP services; |
| ipsec | improved reliability on IPsec hardware encryption for RB1100Dx4; |
| led | added "dark-mode" functionality for SXTsq 5 ac devices; |
| led | use routers uptime as a starting point when turning off LEDs if option was not enabled on boot; |
| sfp | fixed DDM data with SFP+ modules on CRS328-4C-20S-4S+ (introduced in v6.43rc10); |
| sms | do not require "port" and "interface" parameters when sending SMS if already present in configuration; |
| swos | implemented "/system swos" menu that allows to upgrade, reset, save or load configuration and change address for dual-boot CRS devices (CLI only); |
| w60g | improved maximum link distance; |
| w60g | improved RAM memoy allocation processes; |
| wireless | improved Nv2 reliability on ARM devices; |
| Component | Change |
|---|---|
| dhcpv4-client | fixed DHCP client that was stuck on invalid state; |
| dhcpv4-server | fixed DHCP server that was stuck on invalid state; |
| health | changed "PSU-Voltage" to "PSU-State" for CRS328-4C-20S-4S+; |
| health | fixed incorrect PSU index for CRS328-4C-20S-4S+; |
| ike1 | purge both SAs when timer expires; |
| ipsec | use monotonic timer for SA lifetime check; |
| led | added "dark-mode" functionality for hEX S devices; |
| lte | added additional ID support for SIM7600 modem; |
| lte | added support for Quanta 1k6e modem; |
| lte | improved r11e-LTE and r11e-LTE-US dialling process; |
| lte | improved readings of info command results for the SXT LTE; |
| lte | improved stability of USB LTE interface detection process; |
| ntp | allow to specify link-local address for NTP server; |
| ppp | added support for additional ID for E3531 modem; |
| snmp | added remote CAP count OID for CAPsMAN; |
| snmp | fixed readings for CAPsMAN slave interfaces; |
| usb | fixed power-reset for hAP ac^2 devices; |
| usb | properly detect USB 3.0 flash on RBM33G when jumper is removed; |
| userman | improved unique username generation process when adding batch of users; |
| w60g | added distance measurement (CLI only); |
| w60g | improved link stability; |
| w60g | improved maximum link distance; |
| wireless | improved Nv2 reliability on ARM devices; |
| Component | Change |
|---|---|
| backup | generate proper file name when router identity is longer than 32 symbols; |
| bridge | added ingress filtering options to bridge interface; |
| bridge | added initial Q-in-Q support; |
| capsman | increase timeout for the CAP to CAPsMAN communication; |
| certificate | added "expires-after" parameter; |
| certificate | fixed "add-scep" template existence check when signing certificate; |
| chr | by default enable link state tracking for virtual drivers with "/interface ethernet disable-running-check=no"; |
| chr | fixed boot on hosts older than Windows Server 2012 when running CHR on Hyper-V; |
| chr | fixed interface name assign process when running CHR on Hyper-V; |
| chr | fixed MTU changing process when running CHR on Hyper-V; |
| chr | fixed various network hang scenarios when running CHR on Hyper-V; |
| chr | provide part of network interface GUID at the beginning of "bindstr2" value when running CHR on Hyper-V; |
| console | fixed script permissions if script is executed by other RouterOS service; |
| dhcpv6-server | added initial dynamic simple queue support; |
| ipsec | added "responder" parameter for "mode-config" to allow multiple initiator configurations; |
| ipsec | separate phase1 proposal configuration from peer menu; |
| lte | improved modem event processing; |
| ppp | fixed "hunged up" grammar to "hung up" within PPP log messages; |
| ppp | show comments from "/ppp secrets" menu within "/ppp active" menu when client is connected; |
| quickset | added missing wireless "channel-width" settings; |
| quickset | added support for "5ghz-a/n" band when CPE mode is used; |
| quickset | recognize 160 MHz channel as HomeAP mode; |
| romon | fixed RoMON services becoming unavailable after disabled once during active scanning process; |
| supout | added "partitions" section to supout file; |
| switch | added support for port isolation by switch chip; |
| webfig | properly display time interval within Kid Control menu; |
| webfig | properly show NTP clients "last-adjustment" value; |
| winbox | added "poe-fault" LED trigger; |
| winbox | added "secondary-channel" setting to wireless interface if 80 MHz mode is selected; |
| winbox | added missing "dscp" and "clamp-tcp-mss" settings to IPv6 tunnels; |
| winbox | allow to specify full URL in SCEP certificate signing process; |
| winbox | fixed arrow key handling within table filter fields; |
| winbox | properly close session when uploading multiple files to the router at the same time; |
| winbox | removed duplicate "20/40/80MHz" value from "channel-width" setting options; |
| winbox | show "scep-url" for certificates; |
| winbox | show "System/Health" only on boards that have health monitoring; |
| winbox | show firmware upgrade message at the bottom of "System/RouterBOARD" menu; |
| Component | Change |
|---|---|
| dhcp | added dynamic IPv4/IPv6 "dual-stack" simple queue support, based on client's MAC address; |
| dhcp | fixed DHCP server stuck in invalid state; |
| dhcpv4-server | added "allow-dual-stack-queue" implementation (CLI only); |
| dhcpv6-server | added "allow-dual-stack-queue" implementation (CLI only); |
| kidcontrol | added dynamic accept firewall rules in order to allow limit bandwidth when FastTrack is enabled; |
| lte | do not allow to remove default APN profile; |
| snmp | added "rssi" and "tx-sector-info" value support for w60g type interfaces; |
| vrrp | improved reliability on VRRP interface configured as a bridge port when "use-ip-firewall" is enabled; |
| w60g | added distance measurement (CLI only); |
| winbox | by default specify keepalive timeout value for tunnel type interfaces; |
| winbox | show "System/Health" only on boards that have health monitoring; |
| wireless | added option for RADIUS "called-station-id" format selection; |
| wireless | updated "germany 5.8 ap" and "germany 5.8 fixed p-p" regulatory domain information; |
| Component | Change |
|---|---|
| api | changed authentication process (https://wiki.mikrotik.com/wiki/Manual:API#Initial_login); |
| bridge | fixed FastPath for bridge master interfaces (introduce in v6.42); |
| chr | fixed adding MSTI entries; |
| dhcpv6-client | added missing "Server identifier" parameter in release message; |
| kidcontrol | fixed dynamically created firewall rules order; |
| lte | added extended signal information for Quectel LTE EC25 and EP06 modem; |
| lte | added ICCID reading for info command R11e-LTE and R11e-LTE-US (CLI only); |
| user | all passwords are now hashed and encrypted, plaintext passwords are kept for downgrade (will be removed in later upgrades); |
| w60g | added distance measurement (CLI only); |